Miniklio velenas CeramicSpeed BSA29 Coated 73mm for SRAM DUB 29 mm black (105929)

MTB bottom brackets are built with CeramicSpeed Coated bearings and equipped with UFO Long Life Grease for the ultimate in durability and protection in all environments. SRAM DUB crank standard, built on a 29mm spindle, allows for a more contamination resistant BB design, while retaining the ultra-efficient & long-lasting qualities CeramicSpeed Bottom Brackets are known for. With an integrated dust cover for all models, a snug & secure fit that also fully protects the face of the bearing delivers exceptional performance without any sacrifices. CeramicSpeed hand-built bearings carry the load from crank to frame with un-paralleled durability & efficiency. CeramicSpeed COATED Ceramic Bearings - ultimate performance, resistant to corrosion, very low friction, high durability, lifetime warrantyBearing race material: hardened-steelThreading type: BSA29Frame shell size (width): 73 mmUse: MTB bicyclesCompatible with: MTB 29mm SRAM DUB cranksIn the box:2 cups with CeramicSpeed Bearings installed2 dustcovers1 x 3 mm spacer2 x 1 mm spacersSpacer tubeCeramicSpeed Long Life GreaseSticker sheetRELATED TECHNICAL INFORMATION:LIFETIME Warranty of CeramicSpeed Coated Bearings - All CeramicSpeed COATED products are covered by a lifetime* warranty! *PLEASE READ WARRANTY TERMS & CONDITIONS here: https://www.ceramicspeed.com/en/cycling/support/warranty-program/lifetime-warranty-terms-and-conditions CeramicSpeed COATED Ceramic Bearings - Like all CeramicSpeed Bearings, our coated products are handbuilt in Denmark. Building a coated bearing adds a number of extra steps to the process. The CeramicSpeed balls and steel races are matched to the micron after which, each set of races is coated. The races are kept together in pairs through the entire process and after coating, each set needs to pass the quality control before they go into production. CeramicSpeed’s coated products offer the ultimate gains in performance and longevity. The unique coating features several attributes that improve the longevity of CeramicSpeed Bearings. The increased hardness of the races, combined with the smoothness of the CeramicSpeed Balls results in virtually no wear on the bearing. The unique coating is a metallic layer that covers the bearing races and makes them 75% harder than steel. Thanks to this, they are highly resistant to corrosion and the coating provides an even lower friction than our standard bearings. Even if the bearing is contaminated with degreaser, water or mud, the risk of bearing failure due to corrosion is negligible if you choose the coated version.Longetivity comparison diagram: see HEREWithin comprehensive research and development program, the special coating has been developed in cooperation with a European coating specialist. Applied to the bearing’s steel races, through an advanced process that ensures an even, smooth and homogeneous surface, the coating formula improves even further the high quality of CeramicSpeed Bearings.Thanks to the coating’s high resistance to corrosion – even if the bearing is contaminated with degreaser, water or mud, the risk of bearing failure due to corrosion is negligible. We recommend choosing CeramicSpeed Coated Bearings for unmatched longevity and incredibly low friction.Friction comparison diagram (lower is better): see HERELong Life GreaseIt's called Long Life because this grease delivers the best protection and lifetime of your bearings even in the most harsh riding conditions. This is the best choice if you spend your time riding your bike in a humid environment and you do not use coated bearings or if your cycling application is an off-road discipline. Be aware that the Long Life grease has a slightly higher friction coefficient than the standard All Round grease. This is a medium viscosity type of grease, designed to deliver the best performance under the worst riding conditions. The recommended fill rate is 70-100%, depending on the weather conditions and riding application.Maintenance of CeramicSpeed Coated Bearings - Coated Bearings are more resistant to lack of lubrication when it comes to wear and damage on the bearing. Nonetheless, this does not mean that the need for maintenance is completely eliminated.Depending on the riding conditions it is recommended once a year to re-grease your CeramicSpeed Bearings to achieve the best performance in terms of low friction and longevity.If used in very wet or muddy conditions, maintenance might be required more often.If high pressure washer is used, please do not point jet stream to any of bearings (headset, bottom bracket, wheel hub, full suspension links) as it may wash out the grease.